Did you know?

The 264 Traditional Deadbolt has a Lifetime mechanical and finish warranty and a one-year electronics warranty. Please know that we value our consumers’ experience with our products and service, and if there’s any additional support that we can provide, we’re more than happy to help at 1-800-327-5625. Thank you, Kwikset.Enter the default PC (O-O-O-0). Enter the door handing code to re-teach the lock the orientation of the door. Test the lock: WIth the door open and unlocked, press the Kwikset button to make sure it locks the door. Test the default User Code: Enter the default User Code (1-2-3-4), and make sure it unlocks the door.The SmartCode 917 residential electronic lever has been tested in three areas most important to homeowners like you: security, durability, and finish. It is BHMA certified AAA - the highest residential security rating available. It also features SmartKey Security to protect against advanced break-in techniques.This procedure will delete all User Codes associated with the lock, and the default Programming Code (0-0-0-0) and User Code (1-2-3-4) will be restored. 1. Make sure the door is open and unlocked. Press and hold the Reset button for 5 seconds, until you hear 3 long beeps. 2. Enter the default Programming Code (O-O-O-0). 3. Press enter arrow.The default Programming Code is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open. 2. Enter your Programming Code - for new installation, default is 0-0 …Enter your Programming Code. Press enter arrow. You will hear one beep. Press 0. Press enter arrow. You will hear two beeps. The latch bolt will extend and retract to learn the orientation of the door. If successful, you will hear 2 beeps.Follow these simple steps to program your Kwikset Smartcode 260: Start by ensuring the door is open and unlocked. Locate the programming button on the interior part of the lock. Press and hold the programming button for around 5 seconds until the keypad flashes. Release the programming button and enter your desired user code using the …1/8" 3 mm B A C D E 1/8" 3 mm B A C D E 1/8" 3 mm B A C D E 1/8" 3 mm B A C D E 1/8" 3 mm B A C D E 1/8" 3 mm B A C D E Determine which latch will be installed and ...The Programming Code was set up during the initial lock configuration and is required to access programming features. It’s important to note that the provided steps are a general guideline based on typical Kwikset electronic lock functionality, including the Kwikset 264 model.6) Press Kwikset button. 7) Re-enter programming code. 8) Press Kwikset button. You will hear one long beep and the keypad will flash green if successful. If ...How do I add/delete a one-time User Code on my 264 Deadbolt? A one-time user code may be used only once, and then it will be deleted immediately after use. Make sure your door is open and unlocked1. Enter your existing PC (Programming Code).2. Press "Kwikset" then "9" then "Kwikset"3. Enter a new User Code. It must be between 4 and …1. Prepare the Door and Check Dimensions. 2. Install the Latch and Strike. 3. Prepare Keypad and Mounting Plate (Only for Doors with Smaller Holes) 4. Install the Exterior Assembly. 5. Install Interior Assembly. 6. Enter Door Handing Code and Test Lock. 7. Programming. 8. How to Change Your Programming Code. 8. How to Add User Codes. 8. Enter your existing PC (Programming Code). 2. Press "Kwikset" then "4" then "Kwikset". 3. Enter a new PC. It must be between 4 and 10 digits. 4. Press "Kwikset". For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps. Remove battery cover. 3. Press the program button once. 4. Enter new user code. 5. Press lock button. 6. If programming is successful the keypad will flash green once, and you will hear one beep.Door Handing is the process by which the Kevo Smart Lock determines whether the deadbolt faces the right or the left. Door handing instructions: 1. Remove the battery cover. 2. Remove the battery pack from the lock. 3. While holding the Program button, reinsert the battery pack, then release the Program button. 4.6. Test the lock: With the door open and unlocked, press Kwikset. Make sure it locks the door. 7. Test the default User Code: Enter the default User Code (1-2-3-4), then press Kwikset. Make sure it unlocks the door. The default Programming Code is 0-0-0-0. It is recommended that you change it to a code of your own. The lock is pre-programmed ...Locks Kwikset 264 Installation And User Manual. Electronic deadbolt (11 pages) Locks Kwikset Deadbolt Series Quick Installation Manual (2 pages) ... Press the of 12 user codes may again. Program button once. be programmed. User codes should be 4 to 8 During User Code programming, digits in length. ...No user codes are programmed. If there are no codes in the lock, the lock button will not lock the door. Program at least one user code and test the Lock button again. The door handing process was not executed. Perform the door handing process, following the instructions inside the installation guide. The battery is too low to lock the door.6) Press Kwikset button. 7) Re-enter programming code. 8) Press Kwikset button. You will hear one long beep and the keypad will flash green if successful. If ...The 264 Traditional Deadbolt has a Lifetime mechanical and finish warranty and a one-year electronics warranty. Please know that we value our consumers’ experience with our products and service, and if there’s any additional support that we can provide, we’re more than happy to help at 1-800-327-5625. Thank you, Kwikset.Dish Network subscribers can enter the TV code for their television into the remote after pressing and holding down the TV button. Enter in the three or four-digit code on the key ...Browse Kwikset's deadbolts, electronic touchscreen deadbolt locks, and smart door lock conversion kits in a variety of designer styles, finishes and security grades. ... 264 Traditional Keypad Deadbolt. International Series. ... Kwikset SmartCode 911-912: Programming Without a Mastercode. Video Kwikset SmartCode 913-914: …

For security reasons the first 4 digits of each user code must be unique, for example you are unable to program 48151 and 48152If you have disabled user codes you will not be able to add user codes. Read MoreRemove battery cover. 3. Press the program button once. 4. Enter new user code. 5. Press lock button. 6. If programming is successful the keypad will flash green once, and you will hear one beep. SmartKey Security™ re-key technology is compatible with Kwikset (KW1) keyway or (SC1) keyway options. Comes with 2 keys. Deadbolt Latch has 2 interchangeable faceplates - round corner and square corner. ANSI/BHMA grade 2 certified. Latch has adjustable backset 2-3/8" to 2-3/4" to fit all standard door preparations. Includes round deadbolt strike. Enter your existing PC (Programming Code). 2. Press "Kwikset" then "4" then "Kwikset". 3. Enter a new PC. It must be between 4 and 10 digits. 4. Press "Kwikset". For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps. How to change your Programming Code The Programming Code (PC) will not unlock your door. It is an added security feature that is used to set up all functions. The default PC is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Enter your existing PC. 2. Press 4 3. Enter a new PC. It must be between 4 and 10 digits. 4. Press

Features. Installs in minutes with just a screwdriver - no hard wiring required. One touch locking convenience. Easily replaces any standard deadbolt. Featuring SmartKey Security™, which protects against advanced break-in techniques and allows you to re-key your lock yourself in seconds. SmartKey Security™ re-key technology is compatible ...The 264 Traditional Deadbolt has a Lifetime mechanical and finish warranty and a one-year electronics warranty. Please know that we value our consumers’ experience with our products and service, and if there’s any additional support that we can provide, we’re more than happy to help at 1-800-327-5625. Thank you, Kwikset.1. Enter your Programming Code. 2. Press “Kwikset” then “6” then “Kwikset” 3. Enter time between 10 and 99 seconds. 4. Press “Kwikset” For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps. If unsuccessful, the Kwikset button will flash red 3 times and you will ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Are you interested in learning how to code programs? Coding ha. Possible cause: With your user code programmed, you can now unlock the door by entering the.